Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to either replace or install a license-plate bracket on this 2003 GMC Envoy XL.
The first thing you want to do is remove what's left of your old license-plate bracket, if anything. You may have bolts or screws or something that fastens it. Whatever your fastener is, just remove it. In our case, it's clips where you pry out the center and they pull free.
You can see that we had an original license-plate holder on there. The new one from 1A Auto is exactly the same. It's going to all mount the same. I'm just going to put the old one back on, but obviously, if yours has gotten torn off, you'll already have the holes here, and you may already have the fasteners. Ours was held on with this style clip. If you're going to have to hold it on with the clips again, you'll need to drill a hole that's just big enough for the clip to go through. Then as you push the clip in, it widens these legs out and holds. The other possibility you could do is just a course-thread bolt with a washer. In that case, you would want to drill a hole that's slightly smaller than the bolt, and then put it in. Then what you would do is put it on here and just basically place it wherever you might want it. You can go a little higher, go a little lower. The bottom poles do have to be on the bumper cover, though. You could just line those up just above, but put it where you want it height-wise. Try and make sure it's level, and then try to center it kind of using the GMC logo. What I would normally do is I'd drill one hole. I'd put a fastener into the hole and get it held pretty steadily. So you can imagine we've drilled one hole, put a fastener in, and then I'd make sure it's nice and level again. Then I'd drill the second hole, and again, put a fastener in. These things you've got to pull out far enough so the wings can squeeze together. Then just repeat the process for the two lower fasteners.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to either replace or install a license-plate bracket on this 2003 GMC Envoy XL.
The first thing you want to do is remove what's left of your old license-plate bracket, if anything. You may have bolts or screws or something that fastens it. Whatever your fastener is, just remove it. In our case, it's clips where you pry out the center and they pull free.
You can see that we had an original license-plate holder on there. The new one from 1A Auto is exactly the same. It's going to all mount the same. I'm just going to put the old one back on, but obviously, if yours has gotten torn off, you'll already have the holes here, and you may already have the fasteners. Ours was held on with this style clip. If you're going to have to hold it on with the clips again, you'll need to drill a hole that's just big enough for the clip to go through. Then as you push the clip in, it widens these legs out and holds. The other possibility you could do is just a course-thread bolt with a washer. In that case, you would want to drill a hole that's slightly smaller than the bolt, and then put it in. Then what you would do is put it on here and just basically place it wherever you might want it. You can go a little higher, go a little lower. The bottom poles do have to be on the bumper cover, though. You could just line those up just above, but put it where you want it height-wise. Try and make sure it's level, and then try to center it kind of using the GMC logo. What I would normally do is I'd drill one hole. I'd put a fastener into the hole and get it held pretty steadily. So you can imagine we've drilled one hole, put a fastener in, and then I'd make sure it's nice and level again. Then I'd drill the second hole, and again, put a fastener in. These things you've got to pull out far enough so the wings can squeeze together. Then just repeat the process for the two lower fasteners.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Install License Plate Bracket
My salesman dropped off my front license plate bracket today for my 2103 Silverado that was never installed. It has the 4 rivets and two screws. I have been searching for hours tonight trying to find out how to install the bracket and came up empty on the web. Insert your pop rivet into the rivet gun and align the holes on the license plate with those on the license plate holder. Put the rivet in position and squeeze on the rivet gun handles until the rivet shank breaks off. This will usually mean that the rivet has been.
